The Corsi-Rosenthal Cube (sometimes called a Comparetto Cube) is an inexpensive, do-it-yourself air cleaner that can be easily constructed out of a box fan and MERV-13 furnace filters. The Corsi-Rosenthal Cube can give whole-room air cleaning performance comparable to commercial HEPA air cleaners that are 10x or more the cost. Total cost is around $100USD ($130CAD).
- 4 or 5 MERV-13 furnace filters. You will want to purchase 20" sized MERV-13 filters. For the 3M Filtrete brand of furnace filters, this is "FPR 1900." If MERV-13 is not available, MERV-11 filters can be used but performance will not be as great. Important note: see the notes on MERV-13 filter tests below for brands to potentially avoid.
- A 20" box fan
- Duct tape
- Some cardboard
How to construct (Figure 2):
- Duct tape the filters together, forming an incomplete cube. Try to avoid taping over the filter media part of each filter.
- When taping the filters together, make sure to arrange each filter so that the air intake direction of the filter goes inward. The filters should indicate which direction the air is supposed to flow. So you want each filter's airflow direction to point into the cube, not out.
- There should be two empty sides of your incomplete cube. The box fan will go on one of these empty sides and the cardboard will go on the other.
- Cut your piece of cardboard to fit over the bottom area of the cube, where the cube will sit against the ground. Duct tape it to the bottom.
- Duct tape the box fan to the top of the cube. You want the fan to blow air out (not into) the cube. You can also place the fan on the side, rather than the top, of the cube (Figure 3). Having the fan point directly up into the air is a bit better because it's less obtrusive.
- Optional, but strongly encouraged: for increased performance you can create a 'fan shroud'. Cut a piece of cardboard so that the circle created by the fan blades is exposed by the edges of the fan are covered (see diagram or these instructions). You can also use duct tape on the fan to create this 'shroud' as well. The optimal shroud opening has been determined based on the fan brand: For Lasko fans, cut the shroud with an internal diameter (Figure 4) of 15"; for Utilitech fans, use 13.5". For increased durability, you can use Coroplast (corrrugated plastic) or 1/4 inch thick plywood to make the shroud.
Filter brands to potentially avoid
- At least some FilterBuy brand MERV-13 filters have been reported to not perform as expected. As of 2021, FilterBuy appears to be a popular MERV-13 filter vendor on sites like Amazon. If purchasing FilterBuy MERV-13, you may want to test the filters with a particle counter or find some way of ensuring their quality.
5-filter version (Figure 5)
Rather than placing a piece of cardboard on the bottom side of the cube, another filter can be added in place of the cardboard. In this case, you would want to raise the cube off the ground (without blocking the entire bottom filter) so that the bottom filter could be utilized. This would in theory lead to less resistance on the fan motor, potentially prolonging the life of the fan and filters, and increasing the air output.
2-filter "wedge" design (Figure 6)
A variation of the air cleaner can be made using two MERV-13 filters (add details). This version is slightly less expensive (2 fewer filters are needed) and has a slightly smaller footprint.
One filter design, the "classic" DIY box fan air cleaner design.
You can duct tape a single filter to the back of a box fan. In this case there is more strain on the fan motor, more air resistance and the air cleaning efficacy would not be as great. You would also have to replace the filter on the back of the fan more often. But this design has the advantage of having a low footprint and being the least expensive option.
Using a non-box fan (Figure 7)
With some effort (and potentially a lot of duct tape or custom woodworking), you can make a cube using a higher-CFM floor fan. The advantage of this design is that these floor fans put out a lot more CFM than box fans, so the unit will clean the air faster or be better in larger spaces. The downside is it's harder to construct, considerably louder and the cube is less physically stable. There is a guide to constructing a version of one of these using wood.
As discussed in his original blog post, the design for the Corsi-Rosenthal Cube was detailed by Jim Rosenthal, CEO of Tex-Air Filters, and was dedicated to Dr. Richard Corsi. Neil Comparetto also detailed a similar design in a popular YouTube video, which he called a "Comparetto Cube."
- High Quality DIY Box Fan Air Purifier "Comparetto Cube" - video showing how to construct a simple air cleaner cube.
- A Variation on the “Box Fan with MERV 13 Filter” Air Cleaner - original blog post about the cube from Jim Rosenthal
- How to Make a High-MERV DIY Portable Air Cleaner - guide to making an air cleaning cube with instructional pictures.
- Workshop Air Filtration System Performance Shootout - Including Effective, Low-Cost DIY Box Fan Filtration Systems - an overview of various DIY and prebuilt air cleaners for workshop settings.
- David Elfstrom's Twitter account - optimization and effectiveness testing
News / media stories
- Could a Janky, Jury-Rigged Air Purifier Help Fight Covid-19? - Wired article on a simple, earlier version of the DIY air cleaner which uses a single filter taped directly to the back of the fan.